Hold the presses! There has been a change of plans. After playing around with OSMC and some more thinking and drawing, I am going to change course with my Raspberry Pi project. Instead of a fancy pants media center, I am working towards a very nice audio system for the basement living room. My last real stereo was too many years too count and was a very nice Yahmaha system. Tuner, amp, CD, and booming speakers. It has long since gone and have been stuck with my laptop or iPhone with headphones to listen. 

So I have moved in that direction. While working with OSMC I found an inexpensive audio DAC (Digital Audio Converter) HAT, (pizereoaudio.com) for the RPi. 

IMG 9433

When it showed up I heated up the iron and with help of a little hot glue to hold the headers in place was able to solder it in place. 

IMG 9434IMG 9435

Don’t be harsh on some of the joints. While above beginner I am still in amateur phase. 

IMG 9436

I downloaded Volumio2 as the streaming distro. After doing some reading and comparing it seemed like a good package to do with. It supports audio streaming (of course) from local media and network devices. It also supports AirPlay but my first couple of attempts with it haven’t really gone so well. 

The DAC setup was quite easy. In Volumio2, under the menu is the Playback options menu. In there it was as easy as selecting the HiFiBerry DAC. And before I knew it my RPi was singing to me. The Pi Zero Audio DAC is based on the NXP 1334A. A low-power, low-priced DAC. The card was cheap compared to some of the other HATs out there. There is only line out installed on the card, but there are pads on the board is one is so inclined to add RCA jacks. Their documentation is sparse to proceed with caution if take this route. 

Since the pieces and parts are hanging together I whipped up a quick stand for it. 

IMG 9517

It is a piece of sheet metal from something and I superglued 4 standoffs to it. Simple and works for its purpose.

IMG 9516

Here is my proof-of-concept for my streaming player. I tossed on an old set of Altec speakers I had in the Studio. I have to say it really doesn’t sound hateful. Nothing high-end, but working well for what it is. 

Now that I am moving in this direction, I am starting to pick up some parts for the goal of this project, something which has gelled up nicely over the past few days. The end product is to be a single speaker streaming device. The pictures will work better than my words. I will share the drafts of how I want the case for it to look. 

I order the Pi Zero W that will be used for the end product. It came it quickly and I was pretty jazzed to get the headers soldered on and start to set it up as the main streamer.

IMG 9506

Pretty cool huh? And hands to Adafruit for getting it here so quickly. Help me here though, what is wrong with my picture? Where are the headers you ask? Someone forgot to order them. I remember the mini HDMI connector, and the rotary encoder I am going to use for the volume knob, but no headers! DOH! Well, off to eBay and now I am waiting for them to show up. Which is fine, I am still working the my Volumio installation. Songs needs sorted in various directories and playlists, AirPlay needs to be debugged, and I am learning how to add streams for my local radio stations. 

I have found a couple of nice speakers on Amazon from Viston and Dayton. I need to check them out a little more and pick one of them. From Adafruit I have my eye on the 20W amp for the speaker. I am still working on how I want/will power it all. I still have some time for thinking on that one. 

Stay tuned, I will be back to write up on what I have found about the DAC scene for the RPi and a little more about Volumio2. 

© 2017, wrightmac. All rights reserved.

No tags for this post.
wrightmac audio, hardware, Project, Raspberry Pi

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.